The Atlas unit heaters have a big heart: a coil that has been conceived, designed and manufactured specifically for heating industrial environments. The thickness of the pipes, steel as standard, the diameter (Ø 22 mm) and the excellent ratio between the flow-rate of air and the heat output guarantee long life and exceptional comfort. The Atlas unit heaters are made in 10 sizes, with heat outputs from 5 to 120 kW, and are available with 1 row coils for steam or high-temperature water systems, 2 row coils for hot water systems and 3 row coils for low-temperature hot water systems. They can be installed on the wall and on the ceiling.A vast range of accessories, such as additional ducts for taking in outside air and recirculation, flanges, motors with IP 55 protection, explosion-proof motors, multifunction controls with room thermostat, non-standard configurations (special voltages, special pipes) ensures the right solution in all situations.
The HELIOS unit heaters, built with the same criteria of sturdiness and safety that define all Sabiana products, stand out for the splendid new design of the casing, made using anodised aluminium bars and polished die-cast corners. They have the same big heart as the Atlas unit heaters: a coil that has been conceived, designed and manufactured specifically for heating industrial environments. The thickness of the pipes, steel as standard, the diameter (Ø 22 mm) and the excellent ratio between the flow-rate of air and the heat output guarantee long life and exceptional comfort. The Helios unit heaters are made in 6 sizes, with heat outputs from 5 to 60 kW, and are available with 1 row coils for steam or high-temperature water systems, 2 row coils for hot water systems and 3 row coils for low-temperature hot water systems. They can be installed on the wall and on the ceiling.
The Comfort circular unit heaters, for ceiling installation only, are especially suitable for high rooms, even if the optimum ratio between the air flow-rate and the heat output make them suitable for any manufacturing environment. The large heat exchange coil and the fan downstream of the coil ensure optimum mixing of the air in the environment, meaning less stratification of the hot air than with traditional unit heaters. Four different diffusers ensure perfect control of the air flow, with the possibility on the more common diffusers to tilt each louvre in the desired direction. The Comfort unit heaters are made in 10 sizes, with heat outputs from 17 to 107 kW, and one or two speeds motors.
The Polaris circular unit heaters, for ceiling installation only, are especially suitable for high rooms, even if the optimum ratio between the air flow-rate and the heat output make them suitable for any manufacturing environment. The large heat exchange coil and the fan downstream of the coil ensure optimum mixing of the air in the environment, meaning less stratification of the hot air than with traditional unit heaters. When supplied with cold water they can also be used in the summer months, thus allowing cooling at very reasonable costs. The Polaris unit heaters are made in 10 sizes, all fitted with very silent two speeds motors motors, heat outputs from 17 to 107 kW and cooling capacities from 2 to 20 kW.
The Janus unit heaters can be used to economically cool industrial, commercial and sporting facilities, transforming a traditional heating system using unit heaters into a system that can also be used in the summer months, significantly improving the working conditions. The condensate collection tray is built into the appliance, while two-speed motors are fitted as standard. Upon request, controls with thermostat can also be supplied. The Janus unit heaters are made in 4 sizes, each with 3 and 4 row coils, for a total of 8 models, with heat outputs from 16 to 104 kW and cooling capacities from 5 to 28 kW.
The Elegant ECM Sabiana air conditioners allow, at very economical cost, to heat and cool small and medium size environments, like shops, show rooms, workshops, supermarkets. The range is made up of 12 models: 8 RE-ECM models, for heating only, and 4 PE-ECM models, for heating and cooling. All models are for ceiling installation and for hot/chilled water supply. The Elegant series uses an innovative brushless synchronous permanent magnet electric motor controlled by an inverter card that is directly installed on the unit. The heat outputs range from 6 to 26 kW and the cooling capacities from 4 to 10 kW.
The AIX unit heaters are made with stainless steel structures and heat exchange coils with stainless steel pipes and flanged fittings, and aluminium fins. They are available in four sizes, for a total of eight models. These appliances can be supplied with hot water, high-temperature water and steam. They are especially suitable for working environments in which these types of system configurations are required.
The Atlas unit heaters can be supplied with the innovative Jetstream induction flow optimiser, in the manual version or the motorised version for wall-hung or ceiling installation. The lower outlet temperature of the air from the appliances means less stratification of the hot air in the building and less appliance operating time for the same ambient temperature. In addition, the increased air throw means greater uniformity of the temperature at floor level, with an expansion of the comfort zone, and consequently the possibility to install smaller and more silent appliances.
The ATLAS STP thermal barrier system, supplied with hot water, are fitted with special diffusers that create a curtain of hot air. Installed above the door, they deliver a constant vertical flow of air, representing a barrier that, by thermodynamic effect, stops the infiltration of air from the outside, and mixes the residual cold currents. Available in three sizes, with one speed and 1, 2, 3 row coils.
The ELECTRA 90 electric unit heaters with horizontal discharge are made in 7 sizes, with heat outputs from 6 to 36 kW. The electrical heat exchanger has two-stage sealed electrical resistance made of finned steel tubes, to allow part-load operation. The power supply is three phase, 400 V - 50 Hz. The ELECTRAMATIC electric unit heaters with horizontal discharge are made in 5 sizes, with heat outputs from 6 to 24 kW. The electrical heat exchanger has two-stage sealed electrical resistance made of finned steel tubes, to allow part-load operation. The power supply is three phase, 400 V - 50 Hz. These appliances come with an electrical control panel that includes the auxiliary circuits, operating and safety thermostat, and terminal block ready for connection to the line, to the remote control panel and to the room thermostat.
The PRIMULA fan convectors are terminal units designed for heating civil and commercial environments in the place of traditional static radiators. They are available in 3 sizes (1-2kW) in the version with electric heaters.
The No-Strat , an anti-air-stratification appliance, recirculates the hot air downwards, hot air that in large spaces heated with warm air (for example, using hot air generators) tends to stratify towards the top. The temperature controller fitted on the appliance can be used to set the air temperature at which the No-Strat starts operation. In addition, it can be used to increase the recirculation air rate in the volume and improve the uniformity of the ambient temperature. The series includes 8 models, with flow-rates from 3,500 to 14,000 m3/h
The InoxSabiana 25 series is the result of an innovative constructional design aimed at achieving a high quality product, versatility and ease of assembly. The choice of the materials, the use of the latest construction techniques, the care paid to every accessory, the conformity with the European EN 1856-1 standard, the continuous checks on the products and the production process, and the quality mark issued by the prestigious Italian Institute IMQ, guarantee the absolute reliability of the Sabiana flues. The inner wall is made from AISI 316L stainless steel, 0.5 mm thick, while the outer wall is made from AISI 304 stainless steel, 0.5 mm thick, or alternatively copper, 0.6 mm thick. The insulation is rock wool, with a minimum density of 90 kg/m3, 25 mm thick. Longitudinal microplasma welding is used on both the inner and outer wall on each element, while the 90° T sections, flue gas monitoring and inspection module are made using the deep drawing process, thus avoiding welding. All the non-insulated elements are made from AISI 304 stainless steel (aluminium adjustable flashing and storm collar). In addition, the use of an innovative fastening system means that the thermal bridge between the inner and outer wall is reduced to the minimum. The InoxSabiana 25 series includes 8 different inside diameters (from 100 to 350 mm) and a complete series of accessories for solving all problems relating to the discharge of the flue gas from heat generators.
The InoxSabiana 50 series is the result of an innovative constructional design aimed at achieving a high quality product, versatility and ease of assembly. The choice of the materials, the use of the latest construction techniques, the care paid to every accessory, the conformity with the European EN 1856-1 standard, the continuous checks on the products and the production process guarantee the absolute reliability of the Sabiana flues. The inner wall is made from AISI 316L stainless steel, 0.5 mm thick, while the outer wall is made from AISI 304 stainless steel, 0.5 mm thick, or alternatively copper, 0.6 mm thick. The insulation is rock wool, with a minimum density of 90 kg/m3, 50 mm thick. Longitudinal microplasma welding is used on both the inner and outer wall on each element. All the non-insulated elements are made from AISI 304 stainless steel (aluminium adjustable flashing and storm collar). In addition, the use of an innovative fastening system means that the thermal bridge between the inner and outer wall is reduced to the minimum. The InoxSabiana 50 series includes 6 different inside diameters (from 350 to 600 mm) and a complete series of accessories for solving all problems relating to the discharge of the flue gas from heat generators.
The InoxMono series has been designed to offer the maximum guarantee of safety and long life in the discharge of flue gas from heat generators. The choice of the materials, the use of the latest construction techniques, the care paid to every accessory, the continuous checks on the products and the production process, guarantee the absolute reliability of the Sabiana flues. Each element in contact with the flue gas is made from AISI 316L stainless steel, 0.5 mm thick, with longitudinal microplasma welding. All the support and fastening elements are made from AISI 304 stainless steel (aluminium adjustable flashing and storm collar). The male and the female ends of each element are made together using the same belling machine, so as to ensure perfect coupling, with a minimum tolerance of +/- 0.4 mm. The InoxMono series includes 11 different inside diameters (from 80 to 300 mm) and a complete series of accessories for satisfying all installation requirements.
La serie InoxMono comprende 11 differenti diametri interni (da 80 a 300 mm) ed una serie completa di accessori, in grado di soddisfare ogni tipo di esigenza di installazione.
The Duoflex series flexible ducts are a system designed specifically for the renovation of old degraded flues. This system, being flexible, ensures easy tubing operations, even if the vertical path is not regular. The Sabiana Duoflex pipes are made from AISI 316 L stainless steel, with two layers: the outer layer is corrugated section that as well as strengthening the structure, acts as a heat sink, while the inner layer is smooth and therefore offers very low resistance to the flow of flue gas and, at the same time, allows any condensate to run back down. The Duoflex series includes 11 different inside diameters (from 80 to 300 mm) and a complete series of fittings for connection to the Sabiana InoxMono series elements.
